Suzhou Electric Appliance Research Institute
期刊號: CN32-1800/TM| ISSN1007-3175

Article retrieval

文章檢索

首頁 >> 文章檢索 >> 文章瀏覽排名

基于ADAMS的低壓塑殼斷路器操作機構的優化設計

來源:電工電氣發布時間:2019-08-15 13:15 瀏覽次數:723
基于ADAMS的低壓塑殼斷路器操作機構的優化設計
 
王澤濤,遲長春,張夢成,車賽
(上海電機學院 電氣學院,上海 201306)
 
    摘 要:針對某型低壓塑殼斷路器觸頭超程較小的問題,利用UG建立該型斷路器全尺寸三維模型,將模型導入ADAMS中建立其虛擬樣機模型。通過經驗法分析并修改影響觸頭超程的部件,使超程達到技術要求,為減小其動作時間,構建了操作機構的數學模型,對桿件建立方程式,推導后得到連桿長度與桿件夾角之間的變化關系。依靠ADAMS參數化設計工具,以動觸頭角速度最大為優化目標,相關桿件長度為優化變量,對操作機構進行優化設計。仿真結果證明,基于ADAMS的參數化分析法在對復雜運動機構的優化設計中更加高效和便捷,優化結果較為理想,為物理樣機的研制提供了參考。
    關鍵詞:低壓塑殼式斷路器;操作機構;ADAMS優化設計
    中圖分類號:TM561     文獻標識碼:A     文章編號:1007-3175(2019)08-0062-05
 
Optimization Design of Operating Mechanism of Low Voltage Molded
Case Circuit Breaker Based on ADAMS
 
WANG Ze-tao, CHI Chang-chun, ZHANG Meng-cheng, CHE Sai
(School of Electrical Engineering, Shanghai Dianji University, Shanghai 201306, China)
 
    Abstract: Aiming at the problem that the contact over-travel of a low-voltage molded case circuit breaker is small, this paper used UG to establish the full-size three-dimensional model of the circuit breaker and the model was imported into ADAMS to establish its virtual prototype model. The empirical method was used to analyze and modify the components that affected the over-travel of the contact, so that the over-travel could reach the technical requirements. In order to reduce the action time, the mathematical model of the operating mechanism was constructed and the equation was established for the member bar, so as to deduce the relationship between the connecting rod length and the member bar intersection angle. Relying on the ADAMS parametric design tool, this paper took the angular velocity of the moving contact as the maximum optimization target, the relevant member bar length as the optimization variable, to carry out optimization design for the operating mechanism. The simulation results show that this parametric analysis method based on ADAMS is more efficient and convenient in the optimization design of complex motion mechanism, and the optimization result is ideal, which provides a reference for the development of physical prototype.
    Key words: low-voltage moulded case circuit breaker; operating mechanism; ADAMS optimization design
 
參考文獻
[1] 陳德桂,李興文. 低壓斷路器的虛擬樣機技術[M]. 北京:機械工業出版社,2009.
[2] 張俊方. 小型斷路器操作機構仿真及分析[D]. 天津:河北工業大學,2014.
[3] 馬子文,涂煜. 考慮電動斥力的低壓直流斷路器動力學仿真及應力分析[J]. 低壓電器,2013(6):10-14.
[4] 李暢. 新型塑殼斷路器機構綜合與分析[D]. 上海:上海工程技術大學,2016.
[5] 張洵初. CM2塑殼斷路器操作機構研制[D]. 蘇州:蘇州大學,2009.
[6] MITRA A C, FERNANDES E, NAWPUTE K, et al. Development and Validation of a Simulation Model of Automotive Suspension System Using MSC-ADAMS[J].Materials Today: Proceedings, 2018, 5(2):4327-4334.
[7] ZARAFSHAN P, MOOSAVIAN S A A. Dynamics Modelling and Hybrid Suppression Control of Space Robots Performing Cooperative Object Manipulation[J].Communications in Nonlinear Science and Numerical Simulation, 2013, 18(10):2807-2824.
[8] 陳童. 基于ADAMS 的低壓斷路器操作機構仿真平臺的設計研究[J]. 機械設計,2013,30(5):97-100.
[9] HUANG J, SHEN B.Simulation analysis on dynamic protection characteristics of low voltage circuit molded case breakers based on PSCAD/EMTDC[C]//Proceedings of the 33rd Chinese Control Conference,2014:6293-6297.
[10] 劉發英. 基于虛擬樣機的智能塑殼斷路器操作機構模糊可靠性和模糊穩健設計技術研究[D]. 天津:河北工業大學,2014.
[11] 顧建青. 基于ADAMS的高性能塑殼斷路器操作機構研制[D]. 南京:東南大學,2015.
[12] HIREMATH V, VENKATARAM N. Vibration Charecteristics of a High Speed Gearbox Through Dynamic Analysis[J].Materials Today: Proceedings,2017,4(10):10935-10943.
[13] 李建國. 低壓斷路器生產中開距和超程的控制[J].電子技術與軟件工程,2015(3):150.
[14] 潘慶元. 小型斷路器操作機構的運動及靜力分析[J]. 電器與能效管理技術,2018(14):7-12.
[15] 傅亮,孫吉升,王冰青. 基于ADAMS的塑殼斷路器操作機構的仿真優化[J]. 電器與能效管理技術,2018(2):11-18.