雙電源自動轉換開關自動磨合臺研制
肖安建1，陳佳成2，金美玲2
(1 浙江理工大學 機械與自動控制學院，浙江 杭州 310018；
2 杭申集團 杭州之江開關股份有限公司，浙江 杭州 311234)
摘 要：針對傳統自動轉換開關 (ATSE) 磨合臺裝夾慢、磨合效率低，并經常發生磨合中斷等問題，設計出三種能夠有效解決問題的自動磨合臺。給出了設計方案和基本結構，并對三種自動磨合臺進行多角度對比與分析，確立了夾叉式氣動磨合臺為最終方案，經試驗驗證和實際生產應用表明，夾叉式氣動磨合臺經車間使用效果良好，磨合平穩、裝夾方便，氣動磨合效率顯著提高。
關鍵詞：自動轉換開關；自動磨合臺；夾叉式氣動磨合臺
中圖分類號：TM564.8 文獻標識碼：A 文章編號：1007-3175(2022)03-0050-06
Development of Automatic Running-In Platform for Double
Power Automatic Transfer Switch
XIAO An-jian1, CHEN Jia-cheng2, JIN Mei-ling2
（1 School of Mechanical Engineering and Automation, Zhejiang Sci-Tech University, Hangzhou 310018, China;
2 Hangshen Group Hangzhou Zhijiang Switchgear Co., Ltd, Hangzhou 311234, China）
Abstract: The traditional automatic transfer switch (ATSE) running-in the platform has problems, such as slow clamping, low running-in efficiency, frequent running-in interruption, etc. This paper designed three different types of the automatic running-in platform which can effectively solve these problems.This study gave a design scheme and a basic structure of the automatic running-in platform. It conducted a multi-angle comparison and analysis of three automatic running-in platforms and established the clamp-type automatic running-in platform as the final scheme.The experimental verification and actual production application show that the fork-type pneumatic running-in platform has a good use effect in the workshop. The new automatic running-in platform has many advantages. For example, the running-in is stable,the clamping is convenient, and the running-in efficiency has been significantly improved.
Key words: automatic transfer switch; automatic running-in platform; fork-type pneumatic running-in platform
參考文獻
[1] 中國電器工業協會. 低壓開關設備和控制設備 第6-1部分：多功能電器 轉換開關電器：GB/T 14048.11—2008[S]. 北京：中國標準出版社，2009 ：19.
[2] 李秋玲. 自動轉換開關的選型及應用分析[J] . 廣西電業，2020(3) ： 63-66.
[3] 潘巧玉. 探析機械加工中的工裝夾具定位設計[J].設備管理與維修，2021(16) ：133-135.
[4] 連理枝. 低壓斷路器設計與制造[M] . 北京：中國電力出版社，2003.
[5] 陳余進，潘敏，黃偉興，等. 基于 UG 的軟工裝夾具設計[J]. 時代汽車，2021(10) ： 100-102.
